The same living room floor after recoating, with an even warm sheen and the grain still clear.
Timber living room floor before recoating: the boards look dull, with a pale worn patch through the middle and a fireplace behind.

Dugandan · Scenic Rim

Keep the timber.
Renew the finish.

I recoat the floors of whole homes around Boonah, Ipswich and the Scenic Rim. The timber stays put — there’s no sanding machine through the house — so the job is virtually dust-free, with a low-odour water-based finish you can walk on in socks that evening.

From $25/m², GST included.

Why a recoat

A new coat on the floor you already have.

Daily life dulls a timber floor. The hallway goes pale, the table legs leave little arcs in the coating, the west-facing room loses its glow. A recoat puts a fresh finish on the coating that’s still there.

It isn’t a new floor, and it isn’t a sand-back. It’s the job you do while the timber is still sound, so you can put off grinding the boards down. I clean the surface, lightly scuff the old coating so the new one can hold, and roll on a low-odour water-based finish. The house stays virtually dust-free, because there’s no sanding machine.

A recoat

What happens
The existing coating is cleaned, lightly scuffed, and given a new water-based finish. The boards stay as they are.
Dust
Virtually none. There’s no sanding machine in the house.
The household
You stay home. Socks on the floors that evening. Furniture back the next day.
Choose it when
The finish is dull, scratched or tired, but still attached to the timber.

Sanding

What happens
The finish is ground off, and a layer of timber with it, before a new coating goes on.
Dust
Fine timber dust through the house, even with a vacuum on the machine.
The household
Rooms are out of use for longer, and the clean-up is a bigger job.
Choose it when
The coating has failed, the wood itself is damaged, or you want a new colour from bare boards.

If the floor needs sanding, I’ll say so. Worn through to bare timber, gouges into the wood, a coating that’s peeling too badly to hold, or a full colour change — those are sanding jobs. I’d rather point you to a sander than take the job for a coat that won’t last.

Solid timber

Spotted gum, blackbutt, ironbark, tallowwood and the other hardwoods in Scenic Rim houses, plus pine and oak. If a coating is still on the boards, a recoat is usually the right conversation.

Engineered and prefinished

These boards often can’t spare the thickness a sander takes off. A recoat refreshes the factory finish without cutting into the wear layer. Some bamboo is the same — I’ll know from the photos.

Not this job

I don’t recoat laminate, tile or vinyl, and I don’t sand bare boards that have never been finished. Decks, cabinets and outdoor timber are a different trade. Houses only, and the timber floors through the whole home.

How it works

Photos, an empty floor, then the coat.

Four steps. You start them from the kitchen table. I finish them in the house.

  1. 01

    Send photos

    Tell me the suburb, roughly how many square metres of timber, and what’s worrying you — scratches, dull patches, paint, peeling. A link to the real-estate listing helps if the house is on the market. I reply with one fixed price, GST included. There’s no visit just to quote.

  2. 02

    Clear the rooms

    Before I arrive, the timber needs to be empty. Rugs out, furniture off, beds and tables moved. I’ll tell you which rooms when we book. An empty floor is what lets me finish a house in the one visit.

  3. 03

    I recoat the floors

    I wash and vacuum, scuff the old coating so the new one can hold, and lay a low-odour water-based finish. Some floors want a second coat, with drying time between them. We’ll agree the sheen — quieter, or with a little more glow — before I come. I do the work myself.

  4. 04

    Socks on that evening

    You can walk on the floors in socks that evening. Furniture waits until the next day, lifted rather than dragged. Rugs and heavy pieces wait about a week. I’ll walk it through with you before I leave, and leave a short care note.

The weeks after

While it hardens

Socks that evening. Furniture the next day. Rugs, mats and heavy pieces after about a week. The coating keeps hardening for a couple of weeks, so it’s gentle use until then — no heels parked in one spot, no dragged chairs. Humidity and a second coat can shift the timing a little, which is why the care note comes with the job, not as a slogan.

Looking after it

Felt pads under furniture. A soft broom or a hard-floor vacuum, and a damp mop rather than a wet one. No steam mop. Mats inside the doors, and wipe spills instead of leaving them. A sunny hallway wears faster than a bedroom. When water stops beading, it’s worth another conversation — there’s no fixed year count.

Pricing

A clear price, before I set foot in the house.

From 25 dollars per square metre, GST included.

GST included. Whole-house timber recoats.

That’s the rate when the finish is still sound — dull, marked, or lightly scratched in the coating, but holding onto the timber. I quote the floors through the whole home, not a single room.

+ about $5/m²

Heavier prep: paint cleanup, a peeling finish, or light colour correcting. It’s about five dollars a square metre more, still GST included.

Every quote is one fixed, all-in price. GST is in the number. There’s no call-out fee hiding underneath, and nothing gets added on the day if the floor matches the photos. If I arrive and it’s a different job, I stop and talk to you before I start.

A guide for your floor

Pick a house size or type the timber area. This is a guide, not a quote.

Approximate timber floor area
Condition

Indicative total

$2,000

GST included and all in, at the standard rate. A guide, not a quote.

For 80 m² the guide runs from $2,000 to $2,400 if the floor needs extra prep.

The guide uses $25/m² for a sound finish and $30/m² when extra prep is included. Both are GST inclusive. Above $3,300 it asks you to call, instead of showing a figure.

The family behind Scenic Rim Floor Revival, standing on grass in front of a flowering vine and a corrugated iron wall, near Boonah.
Dugandan, near Boonah.

About

A family business, and I do every job myself.

I do every job myself.

Scenic Rim Floor Revival is mine. We live here, in Dugandan on the edge of Boonah, and the floors I recoat are in houses like the ones on our roads — Queenslanders and newer homes whose timber has gone dull in the hallway and a bit scratched under the table.

There’s no crew arriving in a different van, and no handoff to someone you haven’t spoken to. If you send photos, you’re talking to the person who will be in your living room with the roller. I learned the work properly, then brought it home to the Scenic Rim.

You deal with me from the first photo to the care note on the day. That’s the whole business.

Questions

Before you send the photos.

A recoat is a new coat of finish on the floor you already have. I clean the boards, lightly scuff the old coating so the new one can grip, and roll on a water-based finish. The timber stays. I’m not grinding it back to bare wood.

Sanding strips the finish and a layer of timber. It’s noisy, it puts fine dust through the house, and the rooms are out of use for longer. A recoat only refreshes the coating that’s already there, so the job is virtually dust-free.

When the finish has worn through to bare timber, when scratches have cut into the wood, when the old coating is peeling so badly a new coat won’t hold, or when you want a completely different colour from bare boards. Deep water stains in the timber are the same.

If that’s what your photos show, I’ll say so. I’d rather point you to a sander than sell you a coat that won’t last.

Solid timber, engineered boards and prefinished boards that already have a coating. Around here that is often spotted gum, blackbutt, ironbark or a mixed hardwood, and sometimes oak, pine or bamboo. I don’t recoat laminate, tile or vinyl. If you’re not sure what you have, the photos usually settle it.

Yes. I recoat the timber floors through the home, not a single room on its own, and not decks, cabinets or outdoor timber. Houses only — not shops, pubs, offices or schools.

Most homes are finished the day I’m there. You can walk on the floors in socks that evening. Keep furniture off until the next day, and leave rugs and heavy pieces for about a week. The coating keeps hardening for a couple of weeks, so go gently until then.

I’ll leave a short care note, because the weather and the number of coats change the timing a little.

Yes. You don’t need to move out. The finish is low-odour and water-based. Stay off the floor I’m coating, and keep pets off it too, until it’s ready for socks. The rest of the house can carry on.

Yes. Rugs, lounges, beds, tables — anything standing on the timber — need to be off the floor before I arrive, so the coat can go on evenly. If something is too heavy, tell me when you book and we’ll decide whether that room waits.

A recoat keeps the colour the timber already has and puts the life back in the surface. Light colour correcting, to even out a patchy tone, sits in the extra-prep rate. A brand-new stain, starting from bare wood, needs sanding, and I’ll tell you if that’s the case.

Send photos, the suburb and a rough area. I reply with one fixed price, GST included — usually the same day. If the floor matches the photos, that price is the price. Nothing gets added on the day. If I arrive and it’s a different job, I stop and talk to you before I start.

For a sound finish the guide on this page uses $25 a square metre. Heavier prep, such as paint cleanup, a peeling finish or light colour correcting, is about $5 a square metre more.

Felt pads under furniture, and lift things instead of dragging them. A soft broom or a hard-floor vacuum, and a damp mop rather than a wet one. No steam mop. Mats inside the doors, and wipe spills rather than leaving them.

There’s no calendar for the next coat. A sunny hallway wears faster than a bedroom. When water stops beading, or the coating looks dry, send photos again.

Rental houses, yes, including a day between tenancies. I’m based in Dugandan, near Boonah, and I travel to Boonah, Kalbar, Harrisville, Beaudesert, Tamborine, Ipswich, Rosewood, Marburg, Laidley, Springfield and the surrounds.

Service area

From Dugandan, out through the Rim and into Ipswich.

I’m based in Dugandan, on the edge of Boonah. These are the towns I drive to for a whole-house recoat. If you’re a little outside the list, call — the surrounds are part of the round.

  • Boonah
  • Kalbar
  • Harrisville
  • Beaudesert
  • Tamborine
  • Ipswich
  • Rosewood
  • Marburg
  • Laidley
  • Springfield

and surrounds

Free quote

Send a few photos. I’ll send a fixed price.

Name, a phone number, the suburb, and up to three photos of the floors. A listing link helps if the house is on the market. I use this only to reply about the job.

Call 0432 655 507
info@scenicsandlessfloors.com.au

Call now

Your floors

Photos, up to three (optional, and very useful)

What helps in a photo
  1. A wide shot from the doorway, wall to wall.
  2. A low shot along the boards, so scratches and dull patches show.
  3. A close-up of anything peeling, stained, or painted over.

Daylight is enough. You don’t need a flash.